SharkBite Vs Compression Fitting

SharkBite Vs Compression Fitting

Last Updated on July 2, 2023

A sharkbite vs compression fitting can be a confusing decision for the first-time homeowner. These two types of plumbing connections are essentially the same but differ in their work. One difference lies in the fact that the SharkBite has a patented, leak-proof seal. A leaking SharkBite can be fixed by simply reconnecting the pipe. A compression fitting, on the other hand, is not as durable as its soldered counterpart and can’t be reused. It consists of a connector placed over a pipe and a ferrule between the pipe and the fitting. Once this ferrule is in place, the nut tightens the connection between the two.

SharkBite 1/2 Inch Coupling, Push to Connect Brass Plumbing Fitting, PEX Pipe, Copper, CPVC, PE-RT, HDPE, U008LFA
  • INSTALLS IN SECONDS: Repair with no special tools, soldering, crimping, or glue; Just push to create…
  • VERSATILE: SharkBite plumbing valve fittings fit copper, CPVC, and PEX pipe and connect all 3 types…
  • LEAD-FREE: Made of high-quality forged DZR brass that is lead-free. Ball valves, shutoffs, and…

While both fittings are useful, some differences make SharkBite the better option. The SharkBite is easy to install, while the compression fitting creates a tighter fit. Its newness in the market makes it a better choice for first-timers. But if you need a tight fit, you should go with a compression fitting. You can’t always get it right the first time.

Using the SharkBite fitting requires a certain amount of preparation. It requires cutting the pipe with a pipe cutter. Once the hole is drilled, you should use 120-grit sandpaper to polish it. A compression fitting is more durable and will last for up to twenty years. It is a little harder to install than a SharkBite. However, it is much more expensive than the compression.

The advantages of SharkBite are similar to those of compression fittings. A compression fitting requires some preparation. You need to cut the pipe to the proper size with a pipe cutter. Sandpaper is used to polish the pipe before the fitting is fitted. Both of them can be installed with the same tools. But before you choose a particular one, make sure you know how to use it correctly.

Both methods provide a strong seal. Although sharkbite is more expensive, it is more flexible than a compression fitting. It is also easier to install and uses fewer tools. The pros and cons of both are clear: it is the best option for your needs. While sharkbite is cheaper than compression fitting, it is still worth considering if you’re renovating your home. If you’re considering either one, take your time to decide.

SharkBite is more expensive than compression fittings but worth it in the long run. A compression fitting is easier to install and provides a stronger seal. But it is difficult to tighten, which makes it a good choice for DIYers. But, in this case, a SharkBite is better for your plumbing job. There’s no difference between the two types, so make sure you know each type’s pros and cons.

When choosing between sharkbite and compression fittings, keep in mind how both work. As the name suggests, Sharkbites provide a more reliable seal than compression fittings. And they are less expensive to install than compression fittings. In addition, they can be easier to install. But, they are more difficult to pull out of a pipe. If you are looking for a high-quality, long-lasting, leak-proof seal, a SharkBite is best choice.

A SharkBite is more expensive than a compression fitting. A sharkbite needs a copper pipe with enough length to install properly. A compression fitting requires a longer piece of copper pipe. It will also require a rubber O-ring. The two are more likely to be leak-proof. But if you have a large amount of pressure, you might prefer a compressor. But the latter is less expensive.

Another difference between a sharkbite and a compression fitting is the ease of installation. With a compression fitting, you must cut the pipe with a pipe cutter and remove the collar. With a Sharkbite, you need to cut the pipe and then polish it with 120 grit sandpaper. A compression fitting will hold it in place without the help of a plumber, whereas a SharkBite can be installed without any assistance.

SharkBite 3/4 Inch 90 Degree Elbow, Pack of 4, Push to Connect Brass Plumbing Fitting, PEX Pipe, Copper, CPVC, PE-RT, HDPE
  • INSTALLS IN SECONDS: 90 degree elbow pipe connectors requires no soldering, crimping, or glue, just…
  • VERSATILE: Elbow connector fits PEX, copper, CPVC, PE-RT, and HDPE pipe in any combination
  • LEAD FREE: 90 degree elbows are made of durable high quality forged DZR brass which is lead free

Last update on 2023-12-05 / Affiliate links / Images from Amazon Product Advertising API

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top